Car Key Button Repair
A broken car key button can be a hassle. You might need to contact the 24 hour Locksmith Service or purchase an alternative remote.
However, you might be in a position to save money by repairing a worn-out key fob rather than replacing it. This is especially true if an old switch or damaged contacts are the cause of the issue.
Battery
If the buttons on your key fob aren't responding to pressing the buttons, that could be a indication that your battery is dead or nearing the end of its life. It's simple to replace the battery yourself, rather than paying for an auto locksmith or dealership.
First find the battery compartment. It is typically located on the back of the key fob and might be hidden behind an open cover that slides out or an access point that opens when you push the button. Once the compartment has been open then look for the small button-cell battery. It's usually the shape of an ordinary coin and is has a plus and the minus symbol. Remove the battery from the old one and insert a new one in its place, ensuring that the plus and minus symbols are correctly aligned.
Once the battery is in place close the compartment and snap the two halves of the key fob. Before closing the door make sure to align and snap the parts in the correct position. Press any of the buttons to confirm that they work properly.
If your remote keyfob doesn't work after replacing the battery, there could be other problems that require a different type of repair. Physical damage from dropping the fob into a puddle for instance could cause it to stop working altogether. It could also be due to a malfunction with the internal electrical system or need to be deprogrammed. Find out if the issue is with your key fob using these other common car troubleshooting techniques.
Switches
Depending on the year and manufacturer, there are various kinds of switches available that are used in the car keyfob. The older type of key usually has a separate chip which is visible in the case, while the modern keys are more sophisticated and work by sending signals to the car. Whatever the model, the keys' buttons can be damaged or worn out when used regularly. The result is they become difficult to press or even unresponsive. If you press the button too hard it can cause further damage. It may also prevent the key from working in the future.
If you're unable to get your key to function Try changing the batteries. If this doesn't work, you might need to clean your key's fob or re-adjust the switches. These tiny electronic switches are more prone than the larger parts of the key to break due to the fact that they are constantly jostled.
The switches are made of rubber, and they're coated with an electrically conducting film that is prone to wear out over time. Fortunately, they are also small and affordable to replace. The old ones are soldered onto the circuit board, so you'll have to take care to remove them without damaging anything else. You can then solder the new ones into and reassemble your fob.
A good way to keep your car key fob from becoming damaged is to not use it for longer than a couple of hours at a time, and to avoid leaving it in places in areas where it is visible. If you're not using your key, put it away in a secure place.
If the issue persists after you've cleaned the key fob replaced the battery and tried to clean it, you may need to consult an expert locksmith. A professional locksmith will test the frequency of your key to determine whether your vehicle is capable of communicating. They can also open and replace microswitches, change cases, and much more.
Outer Case
A key fob spends much of its time bouncing around and if the buttons aren't free to move upwards and downwards within the case they can get stuck or broken. If cleaning the case with rubbing alcohol and a cotton swab fails to work, it might be necessary to take off the case. If the contacts that the buttons touch aren't a good fit or are worn, changing them might be the only option.
Certain keys have rubber buttons which can wear away over time. Rubber buttons can become hard to press because they stretch, and nails may scratch them. This could cause the key to fail and in this instance it's time for an entirely new case or buttons. This repair involves disassembling the remote, then locating the button switches on the circuit board, then heating the solder before carefully taking them off. New buttons are then soldered to the circuit board. The case can then be put back together with the horseshoe key blade piece inserted. car keys repair must be securely fitted into the case in order to prevent them from falling out.
Inner Case
Over time the buttons on your key fob could become damaged or stuck because of the constant jostling and accidental pressing. If your key fob ceases to function when you're away from home You can fix the issue fast by using metallic tape and punch holes. This allows you to unlock doors but not start the car. This quick fix could allow you to return safely to your vehicle and complete your journey.
